![]() ![]() Note – adding a hastag ‘#’ in place of a numeral in the file name will cause the Omniscan to save subsequent files with consecutively-numbered file names for each punch of the ’SAVE’ button, reducing time between scans if so desired. Confirm ‘Data Selection’ is for ‘All A&C Scans’, and define scan file save name. Reference encoder resolution is 8 counts/mm, site cal gives 7.77 counts/mm.ġ5) Select ‘File’ > ‘Data Settings’. Point n: Repeat above steps for subsequent points until TCG covers inspectionġ4) Select ‘Scan’ > ‘Inspection’. Point 3: Position at 2nd BWE, add TCG gain to bring 2nd BWE to 100% FSH Point 2: Position at 1st BWE, add TCG gain to bring 1st BWE to 100% FSH I haven't ridden, or ridden with, an Arrow equipped Streety. It's certainly less in overall size than the Arrow. Point 1: Position after interface, no TCG gain 1 - 14 of 14 Posts SprintST 2 I went with the Hydroform strictly on looks, and weight, over the Arrow. Check ‘Thickness’ values are the same as entered in Step 9.ġ3) Select ‘Sizing’ Menu ‘Curve Setup’. Satisfaction Guaranteed If you are not happy with Hydroform then let me know within 30 days and your purchase will happily be refunded. Activate C-Scan.ġ1) Select ‘View Settings’ submenu, set Source 1 to ‘Thickness’ Source 2 to ‘A%’ġ2) Select ‘Properties’ submenu. 1.39c File size 45 MB Original link to check out file and buy a license Description Hydroform Water System has AAA quality and performance built by an industry professional. I will say, I had my dealer put the Arrow tune in my bike when I put the Hydrform on. 100% FSH.Ħ) Set Gate ‘I’: Start: -5mm / Width: To cover Interface Echo / Mode: ‘I/’ħ) Set Gate ‘A’: Start: Adjacent to Interface Echo / Width: To cover 1st BWE / Mode: Synchro ‘/’Ĩ) Set Gate ‘A’: Start: Adjacent to Gate A End / Width: To cover 2nd BWE / Mode: Synchro ‘/’ĩ) Select ‘Thickness’ tab in Gates/Alarms menu Source: ‘A/ – I/’, set ‘Min’ to Gate A Start value, set Max to 2 x Nominal Wall thickness (this can be changed at analysis stage, but causes problems if set too low prior to inspection).ġ0) Select ‘Display’ menu. I went with the Hydroform strictly on looks, and weight, over the Arrow. Agitate probe to free water column from bubbles and to ensure steady couplant flow.Ģ) Set display to A-S- (C-Scan left ‘OFF’).ģ) Set Range Start to -5mm to show first interface echo.Ĥ) Reduce Gain until Interface Echo approx. Place Probe assembly on V1 block and flood column with water. Reciever: Bandpass Filter 7.7 MHz / Video Filter: ON / Points Qty: 640ġ) Attach Gasket Plate to Probe Housing. Law: Linear at 0º with Overlap / 4 Element Aperture / First Element: 1 / Hydroform is very fast - without drawing anything else, it renders in the thousands of frames per second. (saved in ‘User’ defined wedges as HydroFORM thk mtl) Wedge: Custom Definition for thick gasket plate:Īngle: 0º Orientation: Normal Height: 31mm Velocity: 1480.00m/s Primary Offset: -30.5mm Secondary Offset: 0.00mm Setup Parameters & Written Instruction for HydroFORM probe (WT in excess of 25mm). ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |